Home > Hard Drive > Hard Drive Ribbon Cable To Sata

Hard Drive Ribbon Cable To Sata

Contents

Registration is free and the forums are specifically for tech issues such as yours.Thank you and I hope you get your issues resolved!Tyler ThompsonPCMechanic Editor-in-Chief[emailprotected] Reply steve scott on November 6, Space to attach dongle. If both drives are set for CSEL and the host interface supports CSEL, but a regular cable is used, both drives will be seen as master. Advertisement cganya Thread Starter Joined: Nov 10, 2009 Messages: 8 i recently tried to plug in a PATA hard drive to my computer in addition to my primary SATA drive. this contact form

Thank you so much in advance for your help! We have a chance to guarantee our right to repair electronic equipment—like smartphones, computers, and even farm equipment. By the sixth you are talking about ‘SATA ports' and ‘SATA drives. PCMech has long been a fan of Acronis True Image. my site

Hard Drive Ribbon Cable To Sata

I've used Syba's IDE/SATA Converter. I have a dell and it was givng me a message that there was no boot drive installed, repeatedly for months. The W2K also detected the new drive when I try check in the ‘device manager'.However, there isn't one WD SATA HD in the explorer.

The connector will not mate. Thanks for the info. Your help is greatly appreciated!Dyan Reply Dyan on December 29, 2007 at 11:32 am Joshcore, can you reply me. Ide Ribbon Cable The connector will not mate.

It is therefore recommended to put disks drives on one cable and CD-ROM and CD burners on the second (a CD burner is installed in exactly the same way as a Ribbon Cable Hard Drive How do I get my computer to recognize it. To do this, the devices must be configured using jumpers located at the rear of the device (beside the IDE connector). It’s yours.

I have a spare one which i utilize as of time while awaiting for its replacement. Hard Drive Ribbon Cable Macbook Pro One problem though - after setting up the new drive and using Norton Ghost 10.0 to clone the old drive, I can't boot from the new drive. Tell them you support a bipartisan bill. Reply Michael Negranol on July 28, 2008 at 11:56 pm A very helpful article, really.

Ribbon Cable Hard Drive

System runs windows xp.If I look at the drives in computer management, both drives show up as healthy, but one is labeled "system" and the other is labeled "page files" There Is there a way that i can create an image of the 40gig and still have my 250 gig unammended?malcolm Reply angie on November 11, 2007 at 3:44 pm hey i Hard Drive Ribbon Cable To Sata In order to use Cable Select jumpering, several conditions must be met. Hard Drive Ribbon Cable To Usb Risley - it's not easy finding good tech support at 10:30, but I've been waiting too long to get this up new drive up and running to wait, and this little

Would you please kindly walk me thru?. weblink Wire 20 is not connected to anything. I originally bought my NO NAME computor from him back in December It first went down in March probally from trying to download free music off Kazzaa. Take Action It's time to speak out for your right to repair. Sata Ribbon Cable Macbook Pro

Reply Graeme on February 2, 2009 at 1:58 pm Thanks for taking the time to write this guide, it was just the manage part i forgot about 🙂 Reply Ginny on If you are installing a 3.5″ drive into a 5.25″ drive bay, you may need to add rails or a mounting bracket to make it fit. Another alternative is to buy an adapter card that plugs into the motherboard and has the sockets you need. http://bornsunsoft.com/hard-drive/sata-hard-drive-not-detected.html With that checked & done, the optical drive's jumpers must be set to the "Slave" position and the drive connected to the middle connector on the ribbon cable. 09-07-2011, 03:06

It is installed, partitioned and formatted but when I try to load XP onto it I get a message saying there is no disc. How To Connect Ide Hard Drive To Sata Motherboard With the new drive as the only HD hooked up, it won't boot and has a disk read error. About The Author PCMech Staff176 Comments Ryan on July 29, 2007 at 1:33 pm For a step by step installation procedure, it would be nice if it was written in plain

wire 28 can be checked for continuity.

Where two devices are connected to the same IDE ribbon cable (the cable which connects one or two IDE devices to the motherboard), we must tell the computer which of the Another way that manufacturers use to make sure that the cable is not reversed is by using a cable key. It's that way for a reason. Ide Hard Drive Jumper Settings HB 199, or the Fair Repair Act, guarantees our right to repair digital equipment like computers, refrigerators, cell phones and tractors.

Reply Glenn on November 7, 2007 at 2:59 am Steve - if all is connected then u must format - see above under ‘Software Installation/Cloning'I've just added a second and had or would i have to clone it?Please reply, greatly appreciate your time.Cheers Reply nick on December 9, 2009 at 6:55 pm i have done everything you have mentioned, when i enter and ur write he DIDNT start off with TAKE drive out of box… jeeees…. his comment is here And they get to set whatever prices they want for parts and service.

How do you format a HD that you cant see then? Reply Cliff on December 11, 2008 at 3:23 pm Dave, Thank you for taking the time and making the effort to publish these instructions. How to backup bookmarks and... [SOLVED] Most Popular B2b Marketplace... Please help.

EXCELLENT!!!!thanks guys for creating this it sure is a help for newbies out there 🙂 as Kyle said waaaaaay back, "I did'nt know that disk management exist" hehehe Reply Bill R I'm somewhat of a techie and i do understand all the jargon. How do i clone the 40gig drive onto the 250gig without formatting the 250gig. small four prong or SATA connection on the drive.

RaybroClick to expand... The primary drive on a channel is called the Master, and the secondary one is called the Slave. ok the c drive does not have that much memary i took the c drive out and tryed to put a new one in but the hook ups on the drive thank you cganya, Nov 10, 2009 #12 Sponsor This thread has been Locked and is not open to further replies.

Reply Jon Amoncio on February 12, 2008 at 3:12 am My motherboard was crashed and need to be replaced. My computer was infected with a Virus so a friend of mine reformatted my computer.

© Copyright 2017 bornsunsoft.com. All rights reserved.