Home > Solved Running > Solved: Running Two Routers In Tandem

Solved: Running Two Routers In Tandem

Sign in 835 148 Don't like this video? Show more unanswered questions Ask a Question 200 characters left Submit Already answered Not a question Bad question Other If this question (or a similar one) is answered twice in this Very straightforward and easy to understand. - Anonymous Everything worked, am happy and found it easy to follow, thank you. - Anonymous Knowing which router needed to be in 'bridged mode' If router 1 has it's wireless on channel 1, use channel 11 on router 2. his comment is here

Both routers are using factory firmware. Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. I personally haven't worked with an air mesh setup nor have I seen it in SOHO/consumer grade equipment. All rights reserved.

For reference, here's a link to a Typical example config using a Netgear router __________________ Remember: Data you don't have at least two copies of is data you don't care about. Ask a Question See Latest Posts TechSpot Forums are dedicated to computer enthusiasts and power users. Tags:local area networkrouterwireless LAN Kolin314 November 16, 2010 at 16:41:53 Specs: Windows 7, AMD Phenom II x4/16GB Hi I hope this request is easy to understand.I use a cable modem which

Connecting two (or more) SOHO broadband routers together. I have a 310NV2 that I would like to use as a wireless access point on the 2nd floor. What you will need is two routers, an ethernet cable running between the two routers (in-wall or along the floors, etc) and a laptop or PC for setup (that's it). Side note: If you're using ISP-provided DSL modems, make sure to put them into transparent bridge mode so you aren't double-NAT-ing your network.

They were looking for a solution with the devices they had on hand so that they wouldn't have to buy more gear (ie, Access Points). Working... This is not common for most retail routers. http://www.tomshardware.com/forum/29684-42-routers-series Note that this application requires NET Framework to run.

Creating your account only takes a few minutes. CNET 200,265 views 3:49 How to use a spare router as a range booster for your Wifi Network - Duration: 8:11. In this case you miss one LAN port to connect another host on R2.With this option both routers MUST be on the same subnet but you save the cost of routing. It will be in hexadecimal numbers 0-f and will look something like this: xx:xx:xx:xx:xx:xx.

Using the lan wire to R2, i it works. http://www.wikihow.com/Connect-Two-Routers But, this complicates matters a whole lot and in the end, it comes down to one simple question:"Why would you want to make more work for yourself and overcomplicate something relatively To upload it to the forum, open the full reply window and use the Manage Attachments button to upload it here. Flag as...

If the mainĀ is an Wireless-AC router and the old/second one is a Wireless-G router, connecting to the "access point" will of course limit your connection speed to G on those devices. this content Here is a link to an over view of the TZ line of products. Yes No Cookies make wikiHow better. The subnet mask is typically 255.255.255.0.

Join the community here. This site is completely free -- paid for by advertisers and donations. TechSpot Account Sign up for free, it takes 30 seconds. weblink Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router.

So summarizing... Two Linksys routers with factory firmware, DHCP Server is 192.168.1.1, Gateway (1st Router) is 192.168.1.2, 2nd Router is 192.168.1.3. 2nd Router will not show up on the network and I can't This will allow you to set up the secondary router further away.

Laptop Two had a corrupt driver, deleted from Device Manager, reinstalled and hey what do you know.

Disable the DHCP server in the secondary router. Connect from the primary router's LAN port to one of the LAN ports on the secondary router. In the near future, will be adding two switches, wifi and hard wire to my home net."..." more - T. cwwozniak, Jul 24, 2013 #2 supaduparocka Thread Starter Joined: Mar 3, 2007 Messages: 158 I have an E1000 (v2, i believe), hooked directly to my cable modem, and a switch on

I am in the same situation.The thing is if it is the same SSID how do i know which one i am connecting to, R1 or R2? This procedure bypasses the routing function (NAT layer) and configures the router as a switch (or wireless access point for wireless routers). Your Account Register | Login Popular Latest Top Reviews September 15, 2014 1553 Star Wars without music (aka "Star Wars Minus Williams - Throne Room") September 30, 2014 507 New GoPro check over here wikiHow Contributor The MAC address it wants is the MAC address of the base station, the router connected directly to the modem.

I had to flash the router with DD-WRT, and even then it required a hardwire. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-over cable. [You will not need a cross-over cable if one of the "routers" is That said, it's usually overkill and can add unnecessary complexity. Devices can share files and resources to any other device on the network.

Ensure that the subnet mask is identical to the primary router. 7 Enter a unique SSID. Even if I set static IP's it was a hassle. Is it R1's LAN IP or R2's? Just want two routers to split the same subnet and share the Gateway and DNS.Many ThanksKolin See More: Two Routers on the same Home Network?

We changed that to "192.168.1.2 to 192.168.1.200". If you have two of the same router, it doesn't matter which one you pick. 2 Determine which router will be the secondary router. Ask a question and give support. Join our site today to ask your question.

Close Yeah, keep it Undo Close This video is unavailable. Method 2 Bridging Two Wireless Routers 1 Determine if your equipment is compatible. Please start a New Thread if you're having a similar issue.View our Welcome Guide to learn how to use this site. Loading...

How to tell? But the BIG drawback is that while all the LAN ports on my routers are 1GB, the WAN ports are 100MB, creating a choking hazard...Clearly the best setup is the simple Browse Securely from Anywhere - Duration: 13:50. Now you should have something similar to the graphic at the top of the article.

An error (403 Forbidden) has occurred in response to this request. Solved: Running two routers in tandem Discussion in 'Networking' started by supaduparocka, Jul 24, 2013. When I try to save the settings I get an error message that says "LAN Subnet conflicts with WAN IP".Did I miss something?Many ThanksKolin Report • #3 wanderer November 17, 2010 Staff Online Now etaf Moderator Advertisement Tech Support Guy Home Forums > Internet & Networking > Networking > Home Forums Forums Quick Links Search Forums Recent Posts Members Members Quick Links

© Copyright 2017 bornsunsoft.com. All rights reserved.